Home USEFUL ARTICLE How to Throw a Cutter( Best Techniques and Procedures)

How to Throw a Cutter( Best Techniques and Procedures)

0

How to Throw a Cutter: How about learning how to throw a cutter? When you throw a cutter or cut fastball, a little sidespin causes the ball to move a few inches in or out. When thrown correctly, the cutter is a deadly pitch that should cause off-balance contact.

How to Throw a Cutter( Best Techniques and Procedures)

How to Throw a Cutter

When you throw a cutter or cut fastball, you’ll toss a fastball with a bit of side spin, which causes the ball to move a few inches in or out.

You do this by slightly off-centering your fastball grip, which is often the 4-seam fastball grip.

Some pitchers place their index and middle fingers slightly toward the outside of the ball while raising their thumb somewhat toward the inside.

However, inexperienced pitchers have a propensity to over-turn their hands into the slider position, causing a “doorknob” movement with the hand that can put stress on the elbow.

Depending on which way they want to cut the ball, the pitcher should keep their thumb in place immediately beneath the ball and simply shift their fingers a bit left or right.

How To Throw A Cutter Like Mariano Rivera

You grip it first like a fastball. The cutter grip is not exactly in the middle. It’s thrown like a fastball, and you should bend your wrist over right at the release point.

The concept is that a left-handed pitcher may cut into a righthander with a fastball that rotates and travels around 59 feet. It hurts a left-hander for a right-handed pitcher.

What are the Steps to Throwing a Cutter?

Follow the steps below;

1. Two-Seam Cut Fastball Grip

The index and middle fingers are used to grasp the two small seams of the baseball when throwing a two-seam fastball.

▸Move your two fingers to the right rather than leaving them where they are. Ensure that your fingers are reasonably close to one another.

You may either place your fingers so that the seam goes exactly along the center of each of them, or so that your middle finger runs down the seam.

▸Position your thumb so that it is perpendicular to your top two fingers.

▸Your wrist should be slightly rotated toward your thumb.

▸Use your middle finger to point. Apply more pressure to your middle finger when throwing a two-seam fastball.

2. Four-Seam Cut Fastball Grip

First, hold the ball as you would a four-seam fastball. The index and middle fingers are used to hold a four-seam fastball, traveling perpendicularly across the U-shaped seams.

▸Put more pressure on your middle finger by bringing your two fingers together and moving them slightly to the right.

▸Keep your thumb anchored at the bottom or maybe higher up within the ball.

3. Delivering the Pitch

Before starting the windup, cover the cut grip with your glove.

You don’t want to reveal your pitch before the ball is really released. Early tipping off of the batter might sabotage the surprise of the pitch.

▸Always keep “fastball” in mind. After all, the cutter is a fastball.

Instead of producing any spin with your wrist, you want to do a basic up-and-down action with your hand.

▸After finishing, snap your wrist down while lightly pressing with your middle finger to create a small amount of spin.

The ball will then travel in on a left-handed hitter and away from a right-handed batter.

Read Also:

What is a Cutter Pitch?

A pitch that is thrown at a high velocity and with a sharp, horizontal movement or cutting action is referred to as a cutter or “cut-fastball.”

Because of its grip and release, this pitch resembles a four-seamer, but it differs from a four-seamer because it travels the glove side rather than the arm side and has a somewhat lower velocity.

A cutter often has minor sidespin along with mostly backspin and gyro spin.

The ball’s backspin makes it move like a four-seamer, and the minor side spin adds a bit of glove-side motion like a slider, resulting in a faster pitch that cuts rather than runs.

How Does a Cutter Move?

We may examine the movement characteristics of our pitches using a Rapsodo.

Cutters, which are highlighted in brown, have a small amount of horizontal break, a majority of their lives to the left of the y-axis, and a positive amount of vertical movement.

We may find pitches between fastballs and sliders. This makes intuitive sense given that this pitch type combines the best qualities of both pitches.

It could be referred to as a “slutter” when a cutter has a lot of runs but little lift.

A pitch with characteristics of both a slider and a cutter is referred to by this moniker.

You can clearly see how the pitch moves by examining its movement profile, which will then help you decide how to deploy it while confronting batters.

Remember that a variety of variables will affect each pitch’s movement characteristics.

It is up to you to put your skills into practice, comprehend the various adjustments that may be made, and keep learning what produces the best results.

If you have any questions concerning How to Throw a Cutter, please feel free to use the comment box below and ask us your question. We will be very pleased to answer you.

You can share this information, with your family and friends, as it will be helpful to someone. Please share it on Twitter, Facebook, G+, Whatsapp or Email it to friends. Use the buttons below to do this.

LEAVE A REPLY

Please enter your comment!
Please enter your name here